Share
Pin
Tweet
Send
Share
Send
![](http://img.uaft2404.org/img/sdela-2019/zazhim-busina.jpg)
To make a Bead clamp you will need:
- clamp.
- blue tape with a width of not more than 25 mm.
- scissors.
- middle for flowers.
- lighter.
- glue gun.
- beads with a diameter of 4 mm.
Creating a Bead jewelry.
The decoration is one large flower, consisting of narrow petals with beads. To start creating this decoration you need to prepare the petals. For this, segments of a blue ribbon 9 cm long are required. In total, 19 pieces are necessary.
![](http://img.uaft2404.org/img/sdela-2019/zazhim-busina-2.jpg)
Exactly in the center of all segments, it is necessary to make a mark on the edge line.
![](http://img.uaft2404.org/img/sdela-2019/zazhim-busina-3.jpg)
To the designated mark, you need to bend the edge of the segment on the right side.
![](http://img.uaft2404.org/img/sdela-2019/zazhim-busina-4.jpg)
Then do the same on the left side, but be sure to make sure that the edge lines are parallel to each other.
![](http://img.uaft2404.org/img/sdela-2019/zazhim-busina-5.jpg)
The resulting triangular parts should be folded in half along the edge lines.
![](http://img.uaft2404.org/img/sdela-2019/zazhim-busina-6.jpg)
The edges held by the fingers should be trimmed with scissors and seared to fasten the tapes together.
![](http://img.uaft2404.org/img/sdela-2019/zazhim-busina-7.jpg)
Focusing on the fold lines running along the top, measure down 5 mm and cut off the rest of the tape. Formed sections must be immediately treated with fire for fixing.
![](http://img.uaft2404.org/img/sdela-2019/zazhim-busina-8.jpg)
It turns out long petals.
![](http://img.uaft2404.org/img/sdela-2019/zazhim-busina-9.jpg)
In total they will turn out 19 pieces.
![](http://img.uaft2404.org/img/sdela-2019/zazhim-busina-10.jpg)
Created parts must be combined together to form a smooth circle.
![](http://img.uaft2404.org/img/sdela-2019/zazhim-busina-11.jpg)
In the center of each petal, one transparent bead should be sewn, placing them closer to the edge.
![](http://img.uaft2404.org/img/sdela-2019/zazhim-busina-12.jpg)
The second row of beads must be sewn 5 mm further, but placing them between the petals. As a result, the petals are curved.
![](http://img.uaft2404.org/img/sdela-2019/zazhim-busina-13.jpg)
From the remaining amount of tape, it remains to prepare a small circle, reaching a diameter of 5 cm. Its edge must be scorched.
![](http://img.uaft2404.org/img/sdela-2019/zazhim-busina-14.jpg)
This item will be the basis for decoration. It must be glued to the bottom of the flower, positioning strictly in the center.
![](http://img.uaft2404.org/img/sdela-2019/zazhim-busina-15.jpg)
On the resulting base, you need to fix the clamp, carefully lubricating it with glue.
![](http://img.uaft2404.org/img/sdela-2019/zazhim-busina-16.jpg)
It remains to straighten the petals and attach the middle for the flowers, closing the center of intersection of the details.
![](http://img.uaft2404.org/img/sdela-2019/zazhim-busina.jpg)
Bead decoration is ready!
Share
Pin
Tweet
Send
Share
Send